Numerical control system parameters change or modification, mechanical failure, CNC machine tool electrical parameters are not optimized motor operation abnormality, CNC machine tool position loop abnormality or control logic is not appropriate, is a common cause of abnormal machining accuracy of CNC machine tools in production, find relevant fault points And processing, CNC machine tools can be restored to normal. In production, it is often encountered that the machining accuracy of CNC machine tools is abnormal. Such faults are highly concealed and difficult to diagnose. There are five main reasons for this type of failure: System parameters mainly include CNC machine feed unit, zero offset, backlash and so on. For example, SIEMENS, FANUC numerical control system, its feeding units are metric and imperial. Some processes in the repair process of CNC machine tools often affect the change of zero offset and gap. The fault processing should be adjusted and modified in a timely manner. On the other hand, due to severe mechanical wear or loose connections, the measured values ​​of the parameters may be changed. It is necessary to make corresponding modifications to the parameters to meet the processing precision requirements of CNC machine tools. A THM6350 horizontal machining center uses the FANUC 0i-MA CNC system. During the milling of the turbine blades, the Z-axis feed anomaly was suddenly found, resulting in a cutting error of at least 1 mm (Z-direction overcut). In the investigation, it was learned that the fault occurred suddenly. The CNC machine tool operated normally in the jog and MDI operation modes, and the reference point was normal. There was no alarm prompt, and the possibility of hard fault in the electrical control part was excluded. The analysis believes that the following aspects should be checked one by one. (1) Check the machining program segment that is running when the accuracy of the CNC machine is abnormal, especially the proofreading and calculation of the tool length compensation and machining coordinate system (G54～G59). A CNC vertical milling machine with FANUC 0-MJ CNC system. During the machining process, the X-axis accuracy was found to be abnormal. The inspection found that there was a certain gap in the X-axis and there was instability when the motor started. When the X-axis motor is touched by hand, the motor shake is more serious, and it is not obvious when starting and stopping. It is more obvious in JOG mode. The analysis believes that there are two reasons for the failure, one is that the mechanical backlash is large; the other is that the X-axis motor is working abnormally. Use the parameter function of the FANUC system to debug the motor. Firstly, the existing gap is compensated; the servo gain parameter and the N-pulse suppression function parameters are adjusted, the jitter of the X-axis motor is eliminated, and the machining accuracy of the CNC machine tool returns to normal. A TH61140 boring and milling machine machining center, the CNC system is FANUC 18i, full closed loop control. During the machining process, the Y-axis accuracy of the machine tool was found to be abnormal, the precision error was at least about 0.006 mm, and the maximum error was 1.400 mm. During the inspection, the machine tool has set the G54 workpiece coordinate system as required. In the MDI mode, a program running “G90 G54 Y80 F100; M30;†is run in the G54 coordinate system. The mechanical coordinate value displayed on the display after the standby bed is finished is “-1046.605â€, and the value is recorded. Then in the manual mode, the Y axis of the machine tool is jogged to any other position, and the above statement is executed again in the MDI mode. After the standby bed is stopped, it is found that the machine coordinate number of the machine tool is "-1046.992", the same as the first The number of displayed values ​​after the second execution is 0.387 mm. In the same way, the Y axis is jogged to a different position, and the statement is executed repeatedly, and the numerical display value is indefinite. Using the dial indicator to detect the Y-axis, it is found that the actual error of the mechanical position is basically the same as the error displayed by the digital display. Therefore, the cause of the fault is that the Y-axis repeat positioning error is too large. Careful inspection of the backlash and positioning accuracy of the Y-axis and re-compensation have no effect. Therefore, there is a problem with the grating scale and system parameters, but why is there such a large error, but the corresponding alarm information does not appear? Further inspection revealed that the shaft was a vertical axis. When the Y-axis was released, the headstock fell down, causing an out-of-tolerance.
Incremental encoders provide speed, direction and relative position feedback by generating a stream of binary pulses proportional to the rotation of a motor or driven shaft. Lander offers both optical and magnetic incremental encoders in 4 mounting options: shafted with coupling, hollow-shaft, hub-shaft or bearingless. Single channel incremental encoders can measure speed which dual channel or quadrature encoders (AB) can interpret direction based on the phase relationship between the 2 channels. Indexed quadrature encoders (ABZ) are also available for homing location are startup.
Incremental Encoder,6Mm Solid Shaft Encoder,Hollow Rotary Encoder,Elevator Door Encoder Jilin Lander Intelligent Technology Co., Ltd , https://www.jllandertech.com
(1) The CNC machine feed unit has been changed or changed.
(2) The zero offset (NULL OFFSET) of each axis of the CNC machine tool is abnormal.
(3) The axial backlash (BACKLASH) is abnormal.
(4) The motor is in an abnormal state, that is, the electrical and control parts are faulty.
(5) Mechanical failure, such as screw, bearing, shaft coupling and other components. In addition, the programming of the machining program, the selection of the tool and the human factors may also lead to abnormal machining accuracy.
(2) In the jog mode, the Z-axis is repeatedly moved, and the motion state is diagnosed by visual, touch, and listening. It is found that the Z-direction motion sound is abnormal, especially the fast jog, and the noise is more obvious. Judging from this, there may be hidden dangers in the mechanical aspect.
(3) Check the Z axis accuracy of CNC machine tools. The Z-axis is moved by the hand pulse generator. (The hand pulse magnification is set to 1×100, that is, the motor feeds 0.1mm for each step change), and the movement of the Z-axis is observed with the dial indicator. The positive movement as the starting point after the one-way motion accuracy is normal, the actual distance of the Z-axis movement of the CNC machine tool d=d1=d2=d3...=0.1mm for each change of the hand pulse, indicating that the motor runs well and the positioning accuracy is good. . The return movement of the number of empty machine tools can be divided into four stages: 1 CNC machine tool movement distance d1>d=0.1mm (slope is greater than 1); 2 shows d=0.1mm>d2>d3 (slope Less than 1); 3 CNC machine tool mechanism does not actually move, showing the most standard backlash; 4 CNC machine tool movement distance and hand pulse set value equal (slope equal to 1), return to the normal movement of CNC machine tools.
Regardless of how the backlash (parameter 1851) is compensated, the characteristic is that, besides the third stage can compensate, other sections still exist, especially the first stage seriously affects the machining accuracy of the CNC machine. In the compensation, it is found that the larger the gap compensation, the larger the moving distance of the first segment.
Analysis of the above inspections suggests that there are several possible reasons: First, the motor has an abnormality; second, there is a mechanical failure; third, there is a certain gap. In order to further diagnose the fault, the motor and the lead screw are completely disengaged, and the motor and the mechanical part are inspected separately. The motor is running normally; in the diagnosis of the mechanical part, it is found that when the screw is moved by hand, the return movement initially has a very obvious feeling of vacancy. Under normal circumstances, the bearings should be able to feel the orderly and smooth movement. After dismantling, it was found that the bearing was damaged and there was a ball falling off. After the replacement, the CNC machine tool returned to normal.
The plc logic control program of the CNC machine tool has been modified, that is, when the Y-axis is released, the Y-axis is first enabled to be loaded, and then the Y-axis is released; and when clamping, the shaft is first clamped, and then The Y axis is enabled to be removed. After the adjustment, the CNC machine tool fault is solved.